. MIMAKI ENGINEERING CO., LTD. TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan Phone: +81-3-5420-8671 Fax: +81-3-5420-8687 D201645-20 URL: http: // www.mimaki. Installing the device.1-2 Where to install the device.1-2 Configuration and Function.1-3 Front Side.1-3 Rear Side.1-3 Operation Panel (JF-1631).1-4 Operation Panel (JF-1610).1-5 Carriage.1-6 Capping Station.1-6 Flushing BOX.1-6 EMERGENCY SWITCH.1-7 Connecting the cables. Turning the power ON.2-4 Setting the media. 2-5 Setting the media on JF-1610.2-5 Setting the media on JF-1631.2-6 Using of Roll Sheet.
Jan 1, 2000 - Zedna Tronic Cbt 0201 Manual Lymphatic Drainage. Please do help me in this regard. 9 Opera Mini is a mobile web browser designed to help.
2-8 Test drawing.2-9 Execution of test drawing. 2-9 Execution of head cleaning. Other useful settings.3-17 Initializing set contents.3-18 For setting media correctly.3-19 CHAPTER 4 Daily Maintenance Routine maintenance.4-2 When the device is left unused for a long period of time.4-2 Notes on cleaning.4-2 Maintenance of frame component.4-3 Ink cartridge. Checking UV ink curing level. 4-41 Adjusting UV light level.
4-42 Checking method of UV illumination intensity.4-43 Check the UV illumination intensity.4-44 CHAPTER 5 In Case of Trouble Before taking a phenomenon as a trouble. 5-2 The device cannot be energized.
In the case where MIMAKI-recommended cable is not used for connection of this device, limits provided by FCC rules can be exceeded. To prevent this, use of MIMAKI-recommended cable is essential for the connection of this device. CAUTION LASER SAFETY This Model is certified as a Class II laser product under the U.S. Department of Health and Human Services Radiation Performance standard according to the Radiation Control for Health and Safety Act of 1968.
This means that this Model does not produce hazardous laser radiation. CDRH REGULATION The Center for Devices and Radiological Health for the U.S. Before starting to operate the printer, be sure to read this Operation Manual carefully. On this operation manual. This Operation Manual describes the operation and maintenance of Model JF-1631/1610 Color Ink Jet Printer (hereinafter referred to as the device).
As the ultraviolet curing device (UV lamp) is mounted, ink curing fixation of ink after printing is allowed. Wide printing width Wide printing width is realized. JF-1631 :1602mm (63 inch) × 3100mm (122 inch) JF-1610 :1602 mm(63inch)x1016mm(40inch) Printing on media having thickness up to 50mm This machine can print on media having thickness up to 50mm. For safe operation Pictorial signs Pictorial signs are used in this Operation Manual for safe operation of and in prevention of damages to the device. Pictorial signs and their meanings are given below. Read and fully understand before reading the text.
For safe operation WARNING. Be sure to setup the appropriate air-moving system in case of using the device in a closed room or a room with bad ventilation. Cautions for constructing exhaust outlet Please observe the following things to prevent the device. (1) The sharp of the exhaust outlet depends on your building enviroment. Never do the following WARNING Do not disassemble or remodel the device Handling of ink cartridges. Never disassemble or remodel the main.
Some of the ingredients (UV Curing unit printer initiator) have toxic consequences to cartridge.Disassembling/remodeling any of aquatic life.Avoid leak into water system or them will result in electric shocks or sewage containing water. Be sure to use only the UV lamp. Use the unit under the power specifications recommended by Mimaki,or it may cause given.Be sure to connect the power cable fire or damages to the unit.Never use UV.
Handling the Anti-freezing liquid. Use the exclusive Anti-freezing liquid by. If you swallowed the Anti-freezing liquid or Mimaki,or the heater may be damaged.
Mixed soft water with antifreezing liquid. If the Anti-freezing liquid or mixed soft.
For safe operation CAUTION Ink cartridges. If the ink cartridge is moved from a cold. You cannot use any other ink type than the place to a warm place, leave it in the room exclusive one.
If you use any other ink temperature for three hours or more before type, it may cause the damage for the using it. UV devices other the UV ink curing level is significantly than those recommended by Mimaki.We lowered.If the UV lamp or silica glass is would take no responsibility for any. For safe operation Notices for installation CAUTION A place exposed to direct A place that is not horizontal A place in which temperature sunlight and humidity vary by a great margin.
Use the device under the following environment. How to Read This Operation Manual This manual provides the explanation about the displayed characters and used keys on the “Display Panel” in addition to the operation procedures. Proceed operations confirming them while using. Where to install the device.1-2 Configuration and Function. 1-3 Front Side.1-3 Rear Side.1-3 Operation Panel (JF-1631).1-4 Operation Panel (JF-1610).1-5 Carriage.1-6 Capping Station.1-6 Flushing BOX.1-6 EMERGENCY SWITCH.
Secure sufficient space for installation before assembling this unit. Decide the place considering the size of the device and a space required for execution of drawing. Machine Type Width Depth Height Total Weight JF-1631 3430 mm 4250 mm (Min.) 1385 to (Max.) 1465mm Approx.1150 kg JF-1610 3430 mm 2005 mm (Min.) 1385 to (Max.) 1465mm. Configuration and Function Front Side Indicator Ink station Indicating a state of the machine. Insert ink cartridges here. P.1-10) P.1-9) ( Carriage ( P.1-6) Table Setting media on it.
( P.2-5) There are absorbing holes on the table so that media is absorbed when vacuum is ON. Operation Panel (JF-1631) The operation panel is used for setting of drawing method and each operation. POWER Lamp Key ( P.2-5) VACUUM/BLOW Lit when the power is ON. Switching VACUUM to BLOW, and vice versa.
TEST VACUUM Lamp ( P.2-5) Press to start the test drawing. Configuration and Function Operation Panel (JF-1610) POWER Lamp Key ( P.2-5) VACUUM/BLOW Lit when the power is ON. Switching VACUUM to BLOW, and vice versa.
TEST VACUUM Lamp ( P.2-5) Press to start the test drawing. Lit when media is set. P.2-9) BLOW Lamp ( P.2-12). Carriage A print head for drawing, a UV irradiation appliance, and a light pointer in the print head cover are mounted on the carriage. Depending on UV lamp condition, the carriage is positioned differently. Capping Station The capping station on the front-right side of the unit consists of the ink caps and suction nozzle used for the maintenance of the print head. Configuration and Function EMERGENCY SWITCH One EMERGENCY switch is placed on the front face of the unit and 2 are placed on each of the buck surface and Y-bar respectively.
When stopping the machine for safety reason, press the switch. Connecting the cables Connecting the USB2.0 interface cable Connect a computer to this machine with the USB2.0 interface cable. Your RIP is required to support USB2.0 interface.
If USB2.0 interface is not installed in your computer, ask a RIP maker near you or our branch office. UV irradiation device and Indicator UV irradiation device. Do not expose your naked eyes directly to the light irradiated from the UV lamp when it lights. Orange. Do not touch the lamp when it is being lit or just after it is Green set OFF. Setting of ink cartridge Use ink cartridge inserting it into the ink station. Kinds of ink that can be used Kind of ink Color Product Number Magenta SPC-0371M Cyan SPC-0371C Yellow SPC-0404HY Black SPC-0371K-2 UV Ink Light cyan SPC-0371Lc Light magenta SPC-0371Lm White SPC-0371W-5.
Never disassemble the ink cartridge. Never refill the ink cartridge with ink. Refilling the ink cartridge can cause a trouble. Remember that Mimaki assumes no responsibility for any damage caused by the use of the ink cartridge replenished with ink. About Media The sizes of media that can be used and the method of handling are described here. The sizes of media that can be used JF-1631 JF-1610 Maximum width 1694 mm Maximum length 3194 mm 1080 mm Max. Drawing width 1602 mm Max.
Menu mode This device has three modes. Each mode is described below. Local Mode Local mode is a mode in drawing preparation state. All keys are available. Receiving of data from the computer is allowed, however, drawing is not executed. The following operations are allowed in the local mode. Operation flow.2-3 Turning the power ON.
2-4 Setting the media. 2-5 Setting the media on JF-1610.2-5 Setting the media on JF-1631.2-6 Using of Roll Sheet. 2-8 Test drawing.2-9 Execution of test drawing. 2-9 Execution of head cleaning. How to use the opening/closing door Close the door while performing the drawing to avoid the bad effect to be caused by UV lamp. When setting the media Set the media after opening the door. When setting the media, avoid contact of the media to the door.
Operation flow Turning the power ON See 'Turning the power ON' P.2-4) Setting the media See 'Setting the media' ( P.2-5) Test drawing See 'Test drawing' ( P.2-9) Execution of head See 'Execution of head cleaning' P.2-10) cleaning Drawing an image from See 'Drawing an image from source data'. Turning the power ON. When the power is turned ON, the Y-bar moves. To avoid injuries, keep your hands away from the table. If the temperature in the hot water device has not reached the predetermined value, a message is indicated. Setting the media. If, within the absorption area, there are suction holes not closed by the media, close such suction holes placing thin sheet form material such as paper, film or tape.
The peripheral parts of the media could roll up due to heat. Fix the media supplementarily using adhesive tapes, etc. Setting the media on JF-1631 Switch over the suction valve at the front of the table adjusting with the size of the media to be set. The valve is opened when the knob is turned vertically and closed when it is turned horizontally.
Setting the media On the absorption area The absorption area of JF-1631 is shown in the following figure. Pressing key, set the FRONT REAR optimum absorption area for the media to be set.
▲ Mark Use as a rough guide for valve opening and closing. Setting the media Using of Roll Sheet Set the roll sheet on the roll sheet hunger on the back face of this device. Test drawing Make test drawing to check whether there is nozzle clogging or other drawing failures (such as wearing or missing). Execution of test drawing.
Printing is disabled when the following messages are displayed. It is enabled when the message has disappeared. Execution of head cleaning When a correct pattern is not obtained in the test drawing, perform the head-cleaning. As for the head cleaning, the following 3 types are available. To be used if ten odd numbers of the lines are missing when the test pattern is normal P.2-10 made.
Execution of head cleaning When cleaning with “Wiping” Press the key in the local CLEANING C L E A N I NG mode. T Y P E: n o r m a l Select wiping with keys C L E A N I NG and press key. Drawing an image from source data Starting the drawing operation.
If the UV irradiation device is not ready or the temperature of the water heating system has not reached the predetermined value, a message is displayed. Drawing is not allowed in such cases.
Drawing an image from source data Interruption of drawing To interrupt the drawing, stop the drawing operation and erase the received data from the device. Press the key while drawing.
Drawing an image from source data Set the moving position by pressing V I EW keys. P O S I T I ON 5 0 0 MM. If you press key, the Y-bar will move to the back of the table centering the origin of the drawing. Turning the power OFF To turn off, check first whether or not there is data received and there remains data that has not yet been output in the device. Turn the power of the connected computer off. Press the power button to cut the power.
CHAPTER 3 Useful Function This chapter describes the setting procedures of each functions, and how to operate the plotter usefully. Changing origin. 3-2 Changing origin with JOG keys. 3-2 Changing origin with FUNCTION menu.3-3 Registering the thickness of the media.3-4 Register the thickness of the media manually. Changing origin The default origin position can be changed. There are following 2 changing methods.
Changing with the JOG keys Changing with the “ORIGIN” in the FUNCTION menu Changing origin with JOG keys Press the keys OR I G I N S E T U P in the local mode. Changing origin Changing origin with FUNCTION menu To precisely set the origin of coordinates, set its X- and Y- coordinates from the FUNCTION menu. This setting value becomes the origin position (0, 0). Press the key in the local FUNCTION F UN C T I ON mode.
Registering the thickness of the media Register the thickness of loading media. There are two ways to register the thickness, one is to register manually and the other is to measure the thickness automatically. Register the thickness of the media manually Press the key in the local FUNCTION. Registering the thickness of the media Measuring the thickness of the media automatically Press the key in the local FUNCTION F UN C T I ON mode.
V I EW Select the HEAD HEIGHT by pressing F UN C T I ON key. Adjusting head gap The value of gap between the head and the media is adjusted. There are 2 setting methods, namely a method of selecting with keys and a method of setting in the “HEADGAP” of the FUNCTION menu.
Adjust head gap with the keys DOWN Press the. Adjusting head gap Registering Head gap value Inputting the value of gap between the head and the media The registered value is reflected on all media. Press the key in the local FUNCTION F UN C T I ON mode. V I EW Press the key. Each setting Setting the print method Settings on printing Press the key in the local FUNCTION F UN C T I ON mode.
V I EW Select the SET UP by pressing F UN C T I ON key. Each setting Item Value Outline STANDARD Standard drawing quality QUALITY FINE High quality drawing (drawing speed is slower) FAST High speed drawing (quality is inferior) Drawing is conducted in both directions when the head moves on the BI-DIR media at drawing. (Quicker drawing compared to “UNI-DIRN”. Setting the light intensity of the UV lamp The light intensity of the UV lamp may be set in 3 stages. This setting is made when the media vulnerable to the heat is used or when the test drawing is made in which the lighting of the UV lamps is not desired.
Each setting Setting of priority Priority of setting of this device or that of the computer on the following items respectively is selected. Items to be selected:Drawing type/ Over-painting Press the key in the local FUNCTION F UN C T I ON mode. Changing language display on the screen Display language can be selected between Japanese and English. Press the key in the local FUNCTION F UN C T I ON mode. V I EW Select the DISPLAY by pressing the F UN C T I ON key. Each setting Output the setting list Keep the list for customer’s record or send it by the fax at inquiry on the maintenance.
Set a larger media than the legal size. P.2-5) ( Press the key in the local FUNCTION F UN C T I ON mode. Displaying machine information of this device Press the key in the local FUNCTION F UN C T I ON mode. V I EW Select the MAINTENANCE by F UN C T I ON pressing the key. Each setting Other useful settings Change settings according to need.
Press the key in the local FUNCTION F UN C T I ON mode. V I EW Select the SET UP by pressing the F UN C T I ON key. Each setting Initializing set contents Press the key in the local FUNCTION F UN C T I ON mode. V I EW Select the SET UP by pressing the F UN C T I ON key. For setting media correctly Guide holes for inserting commercial screws are placed on each end (3 sides) of the table. Fix a guide for placing the media on the correct position using those holes.
For JF-1610, the guide holes are not arranged in the front side. CHAPTER 4 Daily Maintenance Items required for using this unit conveniently, such as an ink replacing method or a cleaning manner, are described. Routine maintenance.4-2 In case defective printing is not When the device is left unused for a resolved. Routine maintenance Be sure to conduct maintenance works for the device depending on operation frequency or periodically so as to use the device for a long time while keeping its drawing accuracy. When the device is left unused for a long period of time. Routine maintenance Maintenance of frame component If the frame components of the device have stained, dampen a poece of soft cloth with water or neutral detergent diluted with water, squeeze it and wipe the frame components clean.
Ink cartridge Replacing with a new ink cartridge Replacing of ink cartridges is required in the following cases. Display on the screen Outline Remaining amount of ink in an ink cartridge is few. Drawing can be continued, but running out of ink may occur during the drawing. I N K N E A R E ND: M Earlier replacement is recommended. Ink cartridge Ink cartridge trouble When an ink cartridge trouble is detected, a warning message appears and printing, cleaning and all other activities that use ink are deactivated. In this case, replace the ink cartridge in question immediately.
Do not leave the ink cartridge unreplaced for a long time as this will cause the nozzle clogging and the printer must be repaired by a service person. Cleaning flushing BOX Replacing waste ink absorption material in the flushing BOX. Contents of the. Maintenance cleaning liquid (SPC-0385) cleaning kit.
Gloves. Paper towel. Goggles. When conducting the replacing, be sure to wear the supplied goggle and gloves since you may get ink in your eyes. Cleaning flushing BOX eplace the absorption material inside the flushing BOX. Replace the absorption material inside the flushing BOX on the left side.
Avoiding dripping of ink droplet at printing Cleaning of the head guard plate Ink droplets caused by drawing may appear on a head guard plate on a bottom face of the carriage. As they can cause stain on media by dripping of ink droplets or drawing trouble, conduct cleaning of the bottom face of the carriage periodically. Avoiding dripping of ink droplet at printing Press the key. ENTER MA I N T E N A N C E S T A T I ON Press the key. ENTER S T A T I ON ME N T: C A RR I A G E o u t Press the key. When the waste ink is pooled up Waste ink used for cleaning the heads will gather in the waste ink tank.
Contact the local dealer or call our branch if you need a spare waste ink tank. Prepare a polyethylene tank for emptying waste tank. When the waste ink is pooled up Disposing of the ink in the wiper tank Screw Open the waste ink box cover.
(1) Remove the screws fixing the both sides of the waste ink BOX cover. (2) Open the cover.
Waste ink box cover Remove the wiper tank and discard the. Replacing the filter of the cooling fan Replace the filter of the cooling fan periodically. (Once around a month). When replacing, be sure to wear the supplied goggles and gloves since you may get ink in your eyes.
Replacing the filter of the cooling fan Remove screws (4 pieces) of the filter Assy. Replace the filtering element. Prepare the new filtering element and replace with filtering element Return the filter Assy to the original state. Attach the filter Assy to the cooling fan and tighten the screws of the upper Finger part. Cleaning nozzle face automatically When predetermined times of printing is completed, nozzle face of the head is cleaned automatically to remove ink droplets stuck to the nozzle face. Select the “PERIODICAL WIPING MODE” of the maintenance menu. (1) Press the key in the local mode.
When media thickness is changed Adjust the ink drop position in drawing by the following operations so as to obtain proper drawing performance when the media thickness is changed in use. Samples of pattern drawn Set a media and the home position for drawing. When media thickness is changed Check the position where the drawn pattern is in one straight line. In the case of the figure in the right, you will notice that a straight line is formed at the point +140. Adjust it by pressing P RN. Changing the ink set The standard ink set of this machine consists of 4 colors (Magenta, Cyan, Yellow, Black) and is changeable to the following ink sets according to user’s purpose Available Ink Sets Ink slot No.
The number of colors (Magenta) (Cyan) (Yellow). Changing the ink set Ink set changing procedures are described below. Example): When “4 colors ink set” is changed to “6 colors ink set”, Select the “INKSET MODE” of the maintenance menu. (1) Press the key in the local mode. FUNCTION (2) Select the MAINTENANCE by pressing key, and press the.
Changing the ink set Set the ink color cartridge indicated on I N K S E T:. m c. the display when the display shown on S E T C A R T R I DG E the right is indicated. In case defective printing is not resolved When the image quality is not improved after repeated head cleanings, perform the filling of the ink. Filling the ink Insert the ink cartridge in the ink station. Set the ink cartridge securely. Press the key in the local FUNCTION.
In case defective printing is not resolved Press the key. ENTER F I L L U P.
Filling of the ink will start. Regular maintenance for white ink White ink is easier precipitate than other inks. In case without printing more than two weeks, white ink may cause precipitate in ink cartridge or inside of the device. When the ink is precipitated, nozzle clogging occurs and normal drawing can not be obtained. Regular maintenance for white ink When a screen shown in the right is WH I T E MA N T displayed,Return the white cartridge to S E T C A R T R I DG E the ink station. As shown in the drawing, set an ink cartridge turning up a side containing the IC chip.
Head maintenance function With the use of the head maintenance function, when the power supply is put ON, the head cleaning and wiping will be performed automatically to prevent the media from being stained. After putting ON the power supply and when the head reaches the set temperature, the cleaning/wiping operation will be performed. Special refresh Set the head frequently to refresh by the following operations when refreshing is required frequently due to drawing failures (blurring or missing) on the data drawn. Select the “SP.REFRESH MODE” of the maintenance menu. (1) Press the key in the local mode.
FUNCTION (2) Select the MAINTENANCE by pressing key, and press the. Cleaning of wiper and cap A cap prevents a nozzle from clogging caused by drying. A wiper sweep ink stuck to a nozzle of the head. The wiper or the cap becomes tainted with ink or dusts during the operation of the device. In order to maintain good condition of the heads, clean the wipers and caps frequently. Cleaning of wiper and cap Remove ink stuck to the wiper and the bracket with the exclusive cleaning swab soaked in the cleaning liquid. If stain or bent of the wiper is too severe, replace the wiper with new one.
Conduct replacing follow the wiper replacement procedure, after completing this operation. Cleaning of wiper and cap Attach the suction nozzle Assy pressing it firmly under the suction nozzle. The wiper M will stick out by around 0.5 mm after being attached. Wipe off the ink and others stuck to the cap with nonwoven cloth. Precautions in handling the antifreeze liquid.
Be sure to wear goggle and gloves for handling the antifreeze liquid. Use the recommended antifreeze liquid by Mimaki. (Antifreeze liquid for replacement: SPC- 0394 1000cc X 2 pieces). Do not touch the antifreeze liquid directly. If the antifreeze liquid settles on the skin or clothes, immediately wash it off with soap and water. Replacement method of antifreeze liquid water There are following two methods for changing the antifreeze liquid mixed water: Make replacement using hot The antifreeze liquid mixed water inside the piping can also be water exchange mode on the discharged completely.
Further, this work is performed safely, as it may maintenance menu. Replacing water in water heater tank Lift the water heating system and engage the hanger with the hook. Remove the hot water tank. Move the remaining antifreeze liquid into a polyethylene tank.
Take care not to spill the antifreeze fluid. If spilled, be sure to wipe it off immediately.
Replacing water in water heater tank Press the key. ENTER WA T E R CHNG S E T A F: e n t Press the key twice to finish. Replacing when the power is turned OFF Make sure that the power supply is turned OFF and remove the blue colored socket.
Replacing exhaust blower Using exhaust blower, the heat generated at the time of making drawings is exhausted. The ink mist sucked in at such time will be hardened and disturb the normal operation of the exhaust blower. Replace the exhaust blower in the following situations: When the exhaust blower does not function normally “ERROR706 UV1 overheat”. Replacing exhaust blower Remove the connecting cable of the exhaust blower from the clamps. Remove the exhaust blower.
Remove the screws (2 pieces), and take out the exhaust blower. Fix the new exhaust blower. Tighten the screws (2 pieces) to fix the exhaust blower.
Setting the UV lamp OFF duration Select the “UV LAMP MODE” of the maintenance menu. (1) Press the key in the local mode. FUNCTION (2) Select the MAINTENANCE by pressing the key, and press the key.
ENTER (3) Select the UV LAMP by pressing the key. Cleaning of UV lamp filter To use for a long time, clean the UV lamp filter periodically (once around two weeks). When cleaning, be sure to wear the supplied goggles and gloves since you may get ink in your eyes.
Cleaning of UV lamp filter Remove the filter holder. Filter holder Remove the mesh filter. The mesh filter is under the UV lamp connector cover. Remove it while pulling the filter.
Mesh filter UV lamp connector cover Clean the mesh filter. Replacing UV lamp The UV lamp is a consumable parts. This units counts the duration of irradiation with the UV lamp to notify the replacing timing. Checking UV lamp irradiation duration Press the key several times in ENTER the local mode. Replacing UV lamp Pull out the exhaust blower Assy upward. Pull out.
After removing the finger screws on the top part of the exhaust blower Assy, pull out the exhaust blower Assy. Exhaust blower Assy Remove UV lamp cassette.
Remove (1) Remove the bolt on the front of the UV lamp cassette using supplied hexagonal wrench. Replacing UV lamp Resetting UV lamp irradiation duration After replacing the UV lamp, reset the irradiation duration stored in this unit. Select the “UV LAMP MODE” of the maintenance menu. (1) Press the key in the local mode. FUNCTION (2) Select the MAINTENANCE by pressing the key, and press the key.
Checking UV ink curing level As the UV lamp is deteriorated, the ink curing level may be lowered. Check the UV ink curing level and adjust the UV lamp light intensity, if necessary. Set media for drawing patterning on the table. Checking UV ink curing level Press the key. ENTER T E S T D R AW. Test drawing starts.
Check the drawing pattern after completion of the drawing. If the UV light intensity goes lower, good drawing pattern cannot be obtained. In this case execute the operation of “Adjusting UV light level”. Checking method of UV illumination intensity UV lamp is a consumable. The more the irradiation time increases, the more the amount of light decreases and the ink will become hard to harden. When the cumulative irradiation time exceeds a certain value, a message prompting you for checking the illumination intensity is displayed on the operation panel.
Check the UV illumination intensity Mount the sensor part of the illumination meter on the illumination meter bracket. (1) Turn over the illumination meter bracket and insert the sensor into the guide part.
Set it with the sensor hole faces downward so that the hole can be seen from the obverse side of the bracket. Checking method of UV illumination intensity Mount the illumination meter bracket on the device. (1) Place the illumination meter bracket and the illumination meter on the left rear of the table. Adjust the rabbet for positioning the illumination meter bracket in order to match to the corner of the adsorption board. Checking method of UV illumination intensity Remove the illumination meter bracket from the device.
The illumination meter bracket is heated by the UV lamp immediately after checking the illumination intensity and if you touch it, you may suffer burns. Remove the illumination meter bracket after being cooled fully.
CHAPTER 5 In Case of Trouble This chapter describes the actions to be taken when the plotter develops any trouble or displays an error message. Before taking a phenomenon as a trouble.5-2 The device cannot be energized.
5-2 The device cannot perform printing. Before taking a phenomenon as a trouble If something is wrong with the device, the buzzer sounds and a corresponding error message is given on the LCD.
Take an appropriate corrective measure in accordance with the message. The device cannot be energized More often than not, this is due to improper connection of the power cable. Corrective measures against troubles in the case where satisfactory image quality is not provided are described in this station. Take measures in accordance with actual state of the picture.
If the measures fail restore the device to the normal state, contact your local MIMAKI distributor or MIMAKI office call for service.: MC Y K K Y CM previous one. The loaded ink cartridge is not.
Use the ink specified by MIMAKI. MIMAKI genuine. N O N - O R I G N L: MC Y K K Y CM. If any error message is given on the LCD, turn off the power to the device and turn it on after a while. If the same error message appears again on the LCD, contact your local MIMAKI distributor or MIMAKI office to call for service.
Error message Cause Corrective measure. Turn off the power to the device an E R R O R 4 0 1 The X motor has been overload. Turn it on after a while. MO T O R X. If the same error message appears again on the LCD, contact your local E R R O R 4 0 2 The Y motor has been overload. Troubles for which error messages are given on the LCD Error message Cause Corrective measure.
![Manual Manual](/uploads/1/2/5/4/125451216/332350781.jpg)
Conduct cap cleaning with reference The time for cleaning the E R R O R 6 0 7 to P.4-26. Capping has come. C A P C L E A N I N G. Troubles for which error messages are given on the LCD Error message Cause Corrective measure.
Execute ink filling. ( P.2-4 ) E R R O R 9 0 1 Certain ink is not filled. N O T C OM P L E T E F U P.
CHAPTER 6 Appendix Tables of specifications and functions of this unit are described. Specifications.6-2 Basic unit specifications.6-2 Specifications for ink.6-3 Position of the warning label. 6-4 Function Flowchart.6-7. UV unit Bottle type (200cc/, with tank full sensor) Waste ink tank USB2.0 compliance Interface MRL-II B Command Less than 55dB Stand-by (FAST-A, 1m in all direction) Operation continuous Noise Less than 65 dB.
Specifications Specifications for ink As for the detail, ask the dealer or our branch. Item Parts No./ Specification Exclusive UV ink cartridge Feature Black, magenta, cyan, yellow, light cyan, light magenta, Ink type white, Clear coat 440CC Capacity of ink cartridge One year from the date of manufacture Shelf life During storage. Position of the warning label This device is adhered with the warning label.
Be sure to fully understand the warning given on the labels. In the case where any of the warning label has become so soiled that the warning message is illegible or has come off, purchase a new one from your local distributor or our office. Position of the warning label No. Lavel M903330 M903763 M903747 M904131 M904148 M903764 LHCM-02 PEC-02 M904130 M902396 M905491 M963239 M905490 M901549 M905122 M905265 M903946. Function Flowchart TEST key T E S T DRAW.
T E S T DRAW. 2. 5 mm NOZ Z L E CHK T E S T DRAW HARDEN CHK F UNC T I ON V I EW 2. 5 mm V I EW S T AR T V I EW S E T V I EW POS S E T UP UV L E V E L S E T UP PR I OR I T Y MA I N T ENANCE PRN. A d j u s t MA I N T ENANCE I NK S E T MA I N T ENANCE UV L AMP MA I N T ENANCE WA T ER CHNG MA I N T ENANCE I N FOMA T I ON MA I N T ENANCE WA I T CA P MA I N V e r 1. 0 0 MA I N T ENANCE MA I N T ENANCE S E L I A L N o. Printed in Japan © MIMAKI ENGINEERING CO., LTD.2008 FW: 2.80.
JF Series is the large format, UV-curable inkjet printer with the versatility to print on numerous uncoated substrates including corrugated plastics, acrylics and uneven or irregular materials. With a maximum resolution of 1200 x 1200 dpi, JF Series is suitable for Sign and POP display graphics for both long and close viewing distances. Using the standard white ink, JF Series can print bright, vibrant color even on transparent and colored media. With the newly developed clear liquid, you can achieve a high-gloss finish while also improving color-fastness. JF Series is equipped with dual UV lamps, enabling high speed, bidirectional printing.
It is a dynamic printer with functions to maximize true flatbed platform advantages. We are pleased to add the new capabilities of flatbed printers to the large format graphics field. The highest resolution of 1,200dpi and the variable dot technology (7 different dot sizes) realize near photographic image quality. Even 4-color mode realizes a non-grainy print. With a minimum dot size of 6pl.,sharp edges of small texts and smoth skin tones can be created. Sample prints on transparent aclylics Without white ink as a basis for overprinting, the colors are not vivid With the white ink overlay print, the images are bright and vivid Beauty of colors is enhanced and color-fastness is also improved. With UV technology,the inks are cured (dried) on the printer.
Prints can be made on uncoated substrates and the prints can be handled immediately. JF series has UV lamps installed on both sides of the carriage, allowing higher production speeds with bidirectional printing. This helps contribute to the machine's high productivity.
Print speed (600x600dpi & 1,200x1,200dpi, 4-color mode & 6/8-color mode) unit:m 2/hr. 4-color mode (bi-directional) 6/8-color mode (uni-directional) JF-1631 JF-1610 JF-1631 JF-1610 resolution pass m 2 sq.ft m 2 sq.ft m 2 sq.ft m 2 sq.ft 600× 600dpi 4pass Hi 18.4 198 17.5 188 -8pass Hi 10.1 109 9.8 105 5.8 62 5.6 60 16pass Hi 5.2 56 5.0 54 2.7 29 2.6 28 1,200× 1,200dpi 8pass 7.6 82 7.3 79 5.0 54 4.9 53 16pass Hi 5.1 55 5.0 54 2.7 29 2.5 27 High performance software RIP helps you utilize the various functions of the JF series 16 bit rendering eliminates tone jump and produces fine color reproduction. Different images can be laid out freely on the RIP. Versatile editing functions such as tiling, trimming, scaling and rotating are provided. Able to network in environments where Windows and Macintosh co-exist.